Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You might locate that your garage door opener has been giving you issues, so you require to repair it. You can repair it by replacing a motherboard, a photo-eye sensor, the primary drive gear, or the set-limit buttons. You can also examine if the security sensing units are working correctly.

Replacing a circuit board

Changing a motherboard for your garage door opener calls for a couple of actions and also tools. Initially, you need to switch off the breaker and disconnect any type of wires. Next, open up the motherboard cover. This will help you to diagnose the issue as well as figure out if you need a new board. Next, get rid of the old board and its cable connectors.

You can then proceed to change the circuit board. The replacement procedure is simple as well as takes around 10 minutes. A brand-new circuit card will set you back concerning $80. To safeguard your brand-new circuit card from power surges, you can buy a surge protector.

Replacing a photo-eye sensing unit

Replacing a photo-eye sensor can be a relatively easy task. Initially, eliminate the sensor from the door and also make certain it is located appropriately. If the sensing unit is angled at all, it may not be getting the right signal, which might be causing the blinking lights. If you discover that the photo-eyes run out positioning, you might need to have a service technician come and also take care of the issue.

The photo-eye sensing unit includes two pieces that mount outside of the door tracks and also towards the flooring. The photo eyes will certainly have a little LED light and also ought to be solid in color. If the light is blinking, its likely the photo-eye is malfunctioning as well as will require to be changed.

Replacing a main drive equipment

To replace a garage door opener major drive equipment, start by getting rid of the cap from the chain pulley. Next off, get rid of the two screws holding the drive equipment to the gear setting up. Now, you can unfasten the three tension pins. Press them from both sides and after that remove them. Then, separate the three cables from the garage door opener motor. These cords should be white, red, and blue.

Once you have eliminated the old equipment, set up a brand-new one. Make sure to grease it well. Place the brand-new equipment right into the shaft, ensuring to line up the mounting holes. Ensure the gear and also sprocket setting up are positioned correctly to guarantee smooth procedure. Next, utilize a hammer and also a nail to drive a pin into the brand-new gear.

Changing the set-limit switches

The first thing you need to do if your garage door is not working appropriately is to examine the set-limit buttons. You may need to adjust them so that the door closes earlier or quits prior to it reaches the flooring. You can examine this by looking at your garage doors manual or online.

To readjust the set-limit switches, youll need a screwdriver or socket. Change the knob clockwise or counterclockwise until the door goes up and also stops, or decreases its range. To look for proper travel distance, determine the space from all-time low of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Key St Ste 105, Keller, TX 76248, USA

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *